40dBm 4G LTE 2600MHz Mobile Phone Signal Repeater Single Band 10W with High Gain
4G LTE 2600MHz Repeater Description:
A professional LTE signal repeater will effectively eliminate the signal blind areas, enhance the network quality, improve the image of cellular operators and bring them more profit, and easy to install and small footprint with no need for expensive transmission lines.
The Single-Band RF Repeater is the kind of repeater used most frequently. It has a simple structure to transparently convey and amplify the wireless signal (at the same frequency) between the BTS (Base Transceiver Station) and mobiles in single wireless network.
The Single-Band RF Repeater is working as a relay between the BTS and mobiles.
It picks up the signal from the BTS via the Donor Antenna, linearly amplifies the signal and then retransmits it via the Coverage Antenna (or the Indoor Signal Distribution System) to the weak/blind coverage area. And the mobile signal is also amplified and retransmitted to the BTS via the opposite direction.
As per operator’s requirement for working frequency, two types of Single-Band RFR are available:
1. Band-Selective Single-Band RF Repeater: to amplify all signals in the whole band (bandwidth is customized);
2. Channel-Selective Single-Band RF Repeater: to amplify only the signals transmitted in the customized 1/2/4/8/16 channels.
4G LTE 2600MHz Repeater Features:
· Aluminum-alloy casing has high resistance to dust, water and corroding;
· AGC (automatic gain control) function to prevent self-oscillation;
· Highly selective channel selector can process multiple channels simultaneously;
· No interference to BTS by adopting linear amplifier with high gain and low noise;
· Adopting filter with highly selectivity and low insertion loss eliminates interference between uplink and downlink;
4G LTE 2600MHz Repeater Application:
To expand signal coverage or fill signal blind area where signal is weak or unavailable.
· Outdoor: Airports, tourism regions, golf courses, tunnels, factories, mining districts, villages, highways…
· Indoor: Hotels, exhibition centers, basements, shopping malls, offices, parking lots.
The Repeater is mainly applicable to such case:
· The repeater can find an installation place which can receive pure BTS signal at strong enough level and can meet the requirement of isolation to avoid self-oscillation;
In comparison with FSR (frequency shift repeater) and FOR (fiber optic repeater), the RFR has the following benefits and disadvantages:
Pro | Con |
· Easy to build the installation site; · Lower cost of equipment and site-building. | · Inappropriate installation may cause self-oscillation; · The Coverage Antenna shall face against the Donor Antenna, which limits the coverage angle; · · High signal noise may be introduced since the Donor Antenna picks up signal from the air; · The repeater shall be installed within the coverage of BTS. |
4G LTE 2600MHz Repeater Specification:
Working Frequency (customizable) | Uplink | 2500 - 2570MHz |
Downlink | 2620 - 2690MHz | |
Working Bandwidth | Customizable | |
Max. Input Level (Non-Destructive) | -10dBm | |
Output Power (customizable) | 40dBm (10 W) | |
Gain | ≥ 90dB | |
Gain Adjustment Range | 1~31 dB @ step of 1dB | |
AGC (Automatic Gain Control) / | >20dB | |
Voltage Standing Wave Ratio (VSWR) | < 1.5 | |
Noise Figure | ≤ 5dB | |
In-Band Ripple | ≤ 3dB | |
Frequency Error | ≤ 0.05ppm | |
Spurious Emission | Within working band | ≤ -15dBm/30kHz |
Out of working band | 9kHz~1GHz: ≤ -36dBm/30kHz | |
1GHz~12.75GHz: ≤ -30dBm/30kHz | ||
Third-Order Intermodulation | ≤ -45dBc/30kHz (measured under rated output power) | |
System Delay | ≤ 5.0μSec | |
I/O Impedance | 50Ω | |
RF Connector | N-Type (Female) | |
Temperature Range | Operation: -25°C ~ +55°C / Storage: -30°C ~ +60°C | |
Relative Humidity Range | ≤ 95% (non condensing) | |
Power Supply (customizable) | DC 48V / AC 85V - 265V, 45Hz - 65Hz | |
Power Consumption | ≤200W | |
Backup Power Supply (optional) | 4 hours | |
Casing Level | IP65 | |
Dimensions(cm) | 75x50x32 | |
Weight(kg) | ≤19 |