PCS1900 Dual Cell Phone Signal Boosters , Mobile Phone Signal Booster GW-17CP-VB
Mobile Phoen Singl Booster Introduction:
Yagi external antenna as included in this kit is suggested when signal outside the home or building is weak. This type outside antenna is a uni-directional antenna that needs to be pointed in the direction of the nearest cell tower of the carrier whose signals need to be boosted inside. It then draws signals from much farther away than an omni-directional antenna would be able to attract. Uni-directional yagi exterior antennas are designed to reach towers that are up to 30 miles away.
Signal Booster GW-17CP-VB is designed to enhance and improve the quality of mobile 2 band CDMA800&1900MHz, connection. There’re black and white colors for options. The Led Indicator will show the current level of the input signal, which simplifies the installation of the external antenna. High quality aluminum shell provides an optimal cooling. This model, as simple in connection, installation and configuration, does not require special skills.
Mobile Phoen Singl Booster Specification:
Frequency Range | Uplink | Downlink | |
CDMA800/GSM850 | 824 - 849MHz | 869 - 894MHz | |
PCS1900MHz | 1850 - 1910MHz | 1930 - 1990MHz | |
Max. Gain | 60dB | 65dB | |
Max. Output Power | 15dBm | 17dBm | |
Band width | Wide Band | ||
Manual Gain Control | 12dB / 1dB Step | ||
Automatic Gain Control | >31dB | ||
Ripple in Band | 8dB; | ||
Noise Figure | ≤ 6dB | ||
VSWR | ≤ 2.0 | ||
Intermodulation Products | 9KHz~1GHz | ≤ -36dBm | |
1~12.75GHz | ≤ -30dBm |
Spurious Emission | 9KHz~1GHz | ≤ -36dBm | ||
1~12.75GHz | ≤ -30dBm | |||
Time Delay | ≤ 1.5 μs | |||
Frequency stability | ≤ 0.01ppm | |||
MTBF | > 50000 hours | |||
Impedance | 50 ohm | |||
Power Supply | AC 90-264V,DC 6V/3A | |||
Power LED | Power indicator | |||
ISO(Alarm LED) | Red | Self oscillation or Strong input signal | ||
ALC>25dB, auto shut down.â | ||||
Green | Normal | |||
Mechanical Specification | ||||
RF Connector | N-Female | |||
Switch | Power Switch | |||
Cooling | Heatsink Convection cooling | |||
Humidity | < 90% | |||
Operating Temperature | -20°C ~ +55°C | |||
Environment Conditions | IP40 | |||
Installation Type | Wall Installation | |||
Size | 182mm×118mm×18mm | |||
Weight | < 1.2Kg |
Mobile Phoen Singl Booster Features:
1. Coverage up to 500 m²
2. ALC Function
3. Simple in connection and installation
4. An optimal cooling with aluminum shell
5. Led indicators show working status and ISO alarm.
6. Support any cellular devices (voice & data & video)
FAQ:
1. After installing booster signal not be very good, indoor signal coverage very small ?
> Adjust outdoor antenna's location and direction
> Change another high gain outdoor antenna
> Check whether cables are connected well
> Change more powerful repeater
2. Cell phone signal full bar, but communication quality bad ?
> Much closer distance between indoor and outdor antenna, separate them with a longer distance.
3. After installing booster not only signal be good, but also more bad ?
> Much closer distance between indoor and outdor antenna, separate them with a longer distance.
4. Working good for long time, suddenly signal bad ?
> Check whether outdoor cable connectors are flooded
> Check whether power light is working normally
> If cables are not flooded and power light is working normally, the booster should has problems and need to be sent back to factory for repair.